Call for testing: Samsung S3 Neo (s3ve3g) owners

flohack

@zenfunk Then please hold VOl-Up, Press power until you get the blue text for recovery. Then, in recovery, use cat /proc/last_kmsg to see what goes wrong there...

zenfunk

https://pastebin.com/pNmtTZ9z

this is last_kmsg

flohack

@zenfunk Ok I will compare with my device. Can you please also send me a getprop output from recovery? Thx

zenfunk

Getprop:
https://pastebin.com/mtLE75cj

flohack

@zenfunk Hmm what OS was installed before? Would you mind trying to reset to Android 5.1? It might have some effect, because otherwise I am not sure whats going on ^^

zenfunk

it was lineage 7.1.
I just reformated /data to ext3, but no improvement.
There are two different kinds of s3 neos around. One with Sony and one with a Samsung camera module. May this be it (not sure which one I have. Will reflash android 5.1 (which one did you use) and then we'll see.
Thank you very much for your time and efforts,
Chris

flohack

@zenfunk Hmm the camera should not block the UI to start, actually. Very weird also that you do not get ssh connection. Did you specify -p ut parameter when installing?

zenfunk

Actually I didn't use -p ut because the script then exits.

./halium-install -p ut ubports-touch.rootfs-xenial-armhf.tar.gz system.img
usage: ./halium-install rootfs.tar[.gz] system.img [release]

positional arguments:
    rootfs.tar[.gz]
    system.img

optional arguments:
    release: run common post installation tasks for release.
             supported: none, halium, pm, ut
             defaults : none

zenfunk

./halium-install ubports-touch.rootfs-xenial-armhf.tar.gz system.img ut

works, I'm trying to boot as we speak. I keep you posted.

zenfunk

Well, with the above command I got to pick a unix password, but still hangs at the boot screen.

flohack

@zenfunk Hmm seems to be the wrong halium-install, how did you get it? The right one has the parameter -p ut as first argument.

zenfunk

I got it from there: https://gitlab.com/JBBgameich/halium-install/-/releases
I downloaded the zip file, unzipped everything, put the imagefiles in the folder as well and ran the script.

flohack

@zenfunk Ohhh thats very old! The continous release is not working anymore it seems. Can you please try to clone the code instead directly? Have you got experience with git?

zenfunk

Funny, I just did this.
The -p ut option works now. dmesg output is:

[ 9620.086869] usb 2-1.2: new high-speed USB device number 20 using ehci-pci
[ 9620.200193] usb 2-1.2: New USB device found, idVendor=18d1, idProduct=d001, bcdDevice= 2.28
[ 9620.200199] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 9620.200203] usb 2-1.2: Product: SAMSUNG_Android
[ 9620.200206] usb 2-1.2: Manufacturer: SAMSUNG
[ 9620.200210] usb 2-1.2: SerialNumber: Halium initrd Debug telnet on port 23 on rndis0 192.168.2.15 - also running udhcpd
[ 9620.207225] rndis_host 2-1.2:1.0 eth0: register 'rndis_host' at usb-0000:00:1d.0-1.2, RNDIS device, 00:00:00:00:00:00
[ 9620.250120] rndis_host 2-1.2:1.0 enp0s29u1u2: renamed from eth0
chris@funkbook:~$ ssh phablet@192.168.2.15
ssh: connect to host 192.168.2.15 port 22: Network is unreachable

On reboots I don't even get the RNDIS device.

Will start over...

zenfunk

I tried again with an 5.1 Android, used the cloned installer, used your heimdall, and now I don't even get to the ubuntu boot screen.

No clue what to do next.

flohack

@zenfunk said in Call for testing: Samsung S3 Neo (s3ve3g) owners:

used the cloned installer, used your heimdall, and now I don't even get to the ubuntu boot screen.

Hmm sounds weird. what does dmesg say

zenfunk

[14506.583270] usb 2-1.2: new high-speed USB device number 41 using ehci-pci
[14506.691529] usb 2-1.2: no configurations
[14506.691542] usb 2-1.2: can't read configurations, error -22
[14506.779122] usb 2-1.2: new high-speed USB device number 42 using ehci-pci
[14507.079205] usb 2-1.2: device descriptor read/64, error -71
[14507.297126] usb 2-1.2: New USB device found, idVendor=18d1, idProduct=d001, bcdDevice= 2.28
[14507.297133] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[14507.297137] usb 2-1.2: Product: SAMSUNG_Android
[14507.297140] usb 2-1.2: Manufacturer: SAMSUNG
[14507.297143] usb 2-1.2: SerialNumber: halium-initrd
[14507.301658] rndis_host 2-1.2:1.0 eth0: register 'rndis_host' at usb-0000:00:1d.0-1.2, RNDIS device, 00:00:00:00:00:00
[14507.362236] rndis_host 2-1.2:1.0 enp0s29u1u2: renamed from eth0

flohack

@zenfunk Looks like now we are kinda stuck with the init. Can you send me again cmdline you used for halium-install?

flohack

I just found out that I linked the wrong halium-install release, in case you dont want to clone. Please use only this: https://github.com/JBBgameich/halium-install/releases

zenfunk

OK, I slept it over and also think that there is something wrong with halium-install.
I clone the script from git, put all the imagefiles in this folder and run:

./halium-install -p ut ubports-touch.rootfs-xenial-armhf.tar.gz system.img

Of course halium-install is not installed system whide that is why I have to use the ./ . I now think that there might be the culprit since your instructions don't use it.
When I use make, it gives me a script called halium-install-standalone.sh in a local bin folder which cannot be installed (no "make install" available). When I run hte standalone script it exits with an error BTW. I found no instructions about how to install the current halium- install system wide. I am sure chucking the script in /usr/bin won't do it :).

~~Your link ( https://github.com/JBBgameich/halium-install/releases) gets me to a page where I don't see any link to download stuff, what am I missing?~~ Edit: found it, it is under Assets.