Jup, version problem. It seems as if heimdall 1.4.1 from the Ubuntu repos is no good, I compiled 1.4.2 and it seems to work. I am rebooting into UB ports right now.
waiting....

I have no clue why, but following @hsce1 's instructions worked for me, I got Ubuntu touch on my SIIIneo. Thanks everyone!!!!

@HMZ47 said in Sony Xperia X Performance F8131:

Wipe system data & cache partitions inside twrp.
Reboot to bootloader and launch the installer.

For me it worked after I formated data inside TWRP and then did the wipes.
Cheers, Christian

I sort of had the same issue today (among others), but a helpful member of the german UBports Telegram group helped me with the install. It runs now- Wohooo!
The trick was to use TWRP to format AND wipe the data partition. Afterwards it went smoothly.
This was addressed in this post already.
Cheers, Christian

I got to play a bit with my new phone today. Wohooooo!

Not sure where to put the bugreports, also, I am not sure if they are halium or ubports specific.
Here they are:

Battery indicator seems to be a bit arbitrary. while on charge and then later while in use it got stuck at two percent for quite some time.

Performance: not very fast most of it is UI related I think. Probably caused by the lack of hardware acceleration? (If so, how could we get this going?)

Couldn't get the Falcon launcher to run. It installed fine but then I never saw a way to activate it.

Scaling of fonts in the UI (via UT tweak tool) is buggy, when set to 20 some Dialogs and screens do not fit hte display anymore.

Cheers and thanks to all involved here,
Christian

I have no clue why, but following @hsce1 's instructions worked for me, I got Ubuntu touch on my SIIIneo. Thanks everyone!!!!

With standalone I don't mean the zipped version. When you do "make" in the cloned folder a script gets creeated that is called halium-install-standalone.sh and that doesn't work.

With systemwide I meant that you seem to have your halium install script in your $PATH since you don't have a ./ in front of your "halium-install" command (if you have, your instructions are wrong).

I used the git clone files and they do not work on my setup (see the four last posts).

OK, I slept it over and also think that there is something wrong with halium-install.
I clone the script from git, put all the imagefiles in this folder and run:

./halium-install -p ut ubports-touch.rootfs-xenial-armhf.tar.gz system.img

Of course halium-install is not installed system whide that is why I have to use the ./ . I now think that there might be the culprit since your instructions don't use it.
When I use make, it gives me a script called halium-install-standalone.sh in a local bin folder which cannot be installed (no "make install" available). When I run hte standalone script it exits with an error BTW. I found no instructions about how to install the current halium- install system wide. I am sure chucking the script in /usr/bin won't do it :).

Your link ( https://github.com/JBBgameich/halium-install/releases) gets me to a page where I don't see any link to download stuff, what am I missing? Edit: found it, it is under Assets.

[14506.583270] usb 2-1.2: new high-speed USB device number 41 using ehci-pci
[14506.691529] usb 2-1.2: no configurations
[14506.691542] usb 2-1.2: can't read configurations, error -22
[14506.779122] usb 2-1.2: new high-speed USB device number 42 using ehci-pci
[14507.079205] usb 2-1.2: device descriptor read/64, error -71
[14507.297126] usb 2-1.2: New USB device found, idVendor=18d1, idProduct=d001, bcdDevice= 2.28
[14507.297133] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[14507.297137] usb 2-1.2: Product: SAMSUNG_Android
[14507.297140] usb 2-1.2: Manufacturer: SAMSUNG
[14507.297143] usb 2-1.2: SerialNumber: halium-initrd
[14507.301658] rndis_host 2-1.2:1.0 eth0: register 'rndis_host' at usb-0000:00:1d.0-1.2, RNDIS device, 00:00:00:00:00:00
[14507.362236] rndis_host 2-1.2:1.0 enp0s29u1u2: renamed from eth0

I tried again with an 5.1 Android, used the cloned installer, used your heimdall, and now I don't even get to the ubuntu boot screen.

No clue what to do next.

Funny, I just did this.
The -p ut option works now. dmesg output is:

[ 9620.086869] usb 2-1.2: new high-speed USB device number 20 using ehci-pci
[ 9620.200193] usb 2-1.2: New USB device found, idVendor=18d1, idProduct=d001, bcdDevice= 2.28
[ 9620.200199] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 9620.200203] usb 2-1.2: Product: SAMSUNG_Android
[ 9620.200206] usb 2-1.2: Manufacturer: SAMSUNG
[ 9620.200210] usb 2-1.2: SerialNumber: Halium initrd Debug telnet on port 23 on rndis0 192.168.2.15 - also running udhcpd
[ 9620.207225] rndis_host 2-1.2:1.0 eth0: register 'rndis_host' at usb-0000:00:1d.0-1.2, RNDIS device, 00:00:00:00:00:00
[ 9620.250120] rndis_host 2-1.2:1.0 enp0s29u1u2: renamed from eth0
chris@funkbook:~$ ssh phablet@192.168.2.15
ssh: connect to host 192.168.2.15 port 22: Network is unreachable

On reboots I don't even get the RNDIS device.

Will start over...

I got it from there: https://gitlab.com/JBBgameich/halium-install/-/releases
I downloaded the zip file, unzipped everything, put the imagefiles in the folder as well and ran the script.