Sony Xperia X (suzu/F5121 & F5122)

Hris

This post is deleted!

Linux Klaus

@fredldotme thank you so much for your awesome work. I just flashed the port a few days ago and everything is working super smooth.

I followed during the installation process your instructions and of @christophe14 (post 160). It helped me a lot.

The ubports installer caused a lot of trouble during the installation. I got a lot of error messages (they are already on github). The biggest problem for me was for some reason to boot into fastboot mode. It took me easily 40 attempts. Don't know why. For some reason the ubports installer also did not recognised the device (all the necessary drivers were installed. Switched over to the installer on fedora and did not had any problems.

Keep up the great work. I am amzed by this wonderful community and what you all have already achieved.

c4pp4

@jro
What is the output of

adb shell ls

when the device is connected in recovery mode?

c4pp4

Some audio tweak:

boot device into recovery
mount system.img:

adb shell mount /system/var/lib/lxc/android/system.img /tmp

when playing 44.1 kHz audio stream the sound is crackling, default sample rate is 48 kHz and I think the resampler is too slow, fix it using higher latency via deep buffer flag:

adb pull /tmp/etc/audio_policy.conf
sed -i '/AUDIO_OUTPUT_FLAG_PRIMARY/{s/FAST/DEEP_BUFFER/}' audio_policy.conf
adb push audio_policy.conf /tmp/etc

ringtone volume is too low, it's played via output-speaker+wired_headphone port, set appropriate acdb_id:

adb pull /tmp/etc/audio_platform_info.xml
sed -i '/Custom mapping starts here/a \        <device name="SND_DEVICE_OUT_SPEAKER_AND_HEADPHONES" acdb_id="799"/>' audio_platform_info.xml
adb push audio_platform_info.xml /tmp/etc

sound is distorted when max volume is used, correct max volume:

adb pull /tmp/etc/mixer_paths.xml
sed -i -e '/RX7 Digital Volume/{s/92/86/}' -e '/RX8 Digital Volume/{s/92/86/}' mixer_paths.xml
adb push mixer_paths.xml /tmp/etc

umount system.img:

adb shell umount /tmp

reboot the device

flohack

@c4pp4 Wonderful, aber you able to integrate this permanently into the system image with a PR on Github? Your solution is too complex to apply and also will be overwritten by an update

fredldotme

Yeah, those changes presented as a PR would be highly appreciated! I'm currently occupied with a lot of other things, so I probably can't do it myself in the short term. The files you're modifying are probably in the suzu and loire repos on GitHub linked in the top post.

fredldotme

Thanks again to @c4pp4 for preparing those changes as a pull request, the changes will land within the next two days.

c4pp4

@fredldotme
No problem

I'm trying to achieve 44.1 kHz as the default rate or find out why is resampler too slow. I'm not sure if it's pulseaudio server, droid module or qcom driver related or something else.

c4pp4

@fredldotme
I think I find out why it's always using 48 kHz. It's related to qcom/audio/hal. According to this commit https://github.com/fredldotme/device-sony-common/commit/b3235f337a371d7746fe591e3adcaca99c90dc4f we are using qcom/audio/default/hal/audio_hw.c where adev_open_output_stream function is always assigning 48 kHz rate regardless of what we configure in audio_policy.conf/touch.pa:

3065       out->sample_rate = out->config.rate

newer version contains:

5295       if (config->sample_rate == 0) {
5296                   out->sample_rate = out->config.rate;
5297               } else {
5298                   out->sample_rate = config->sample_rate;
5299       }

Is there a chance to test patched version?

Giampy

This post is deleted!

fredldotme

@c4pp4 you could build your own Halium image and test it that way. The build instructions are here: https://github.com/Halium/projectmanagement/issues/98

Just build the systemimage, run simg2img, e2fsck and resize2fs on it and put it in /system/var/lib/lxc/android/system.img.

c4pp4

@fredldotme
Thank you!

c4pp4

@fredldotme
I've patched it and successfully built and tested.

patch:

diff -Nur a/hardware/qcom/audio/hal/audio_hw.c b/hardware/qcom/audio/hal/audio_hw.c
--- a/hardware/qcom/audio/hal/audio_hw.c	2020-06-03 09:11:31.406960000 +0200
+++ b/hardware/qcom/audio/hal/audio_hw.c	2020-06-03 23:34:16.000000000 +0200
@@ -3033,6 +3033,8 @@
                 out->format = audio_format_from_pcm_format(out->config.format);
             }
         }
+        if (config->sample_rate != 0)
+            out->config.rate = config->sample_rate;
         out->sample_rate = out->config.rate;
     }
     ALOGV("%s: Usecase(%s) config->format %#x  out->config.format %#x\n",

adb shell pacmd list-sinks:

2 sink(s) available.
  * index: 0
	name: <sink.primary>
	driver: <module-droid-card.c>
	flags: HARDWARE DECIBEL_VOLUME LATENCY 
	state: SUSPENDED
	suspend cause: IDLE 
	priority: 9000
	volume: front-left: 65536 / 100% / 0,00 dB,   front-right: 65536 / 100% / 0,00 dB
	        balance 0,00
	base volume: 65536 / 100% / 0,00 dB
	volume steps: 65537
	muted: no
	current latency: 0,00 ms
	max request: 0 KiB
	max rewind: 0 KiB
	monitor source: 0
	sample spec: s16le 2ch 44100Hz
	channel map: front-left,front-right
	             Stereo
	used by: 0
	linked by: 1
	fixed latency: 10,00 ms
	card: 0 <droid_card.primary>
	module: 4
	properties:
		device.description = "Droid sink primary"
		device.class = "sound"
		device.api = "droid-hal"
		droid.flags = "AUDIO_OUTPUT_FLAG_PRIMARY|AUDIO_OUTPUT_FLAG_FAST"
		droid.hw_module = "primary"
		device.icon_name = "audio-card"
		droid.output.primary = "true"
		droid.output.low_latency = "true"
		droid.output.media_latency = "true"
	ports:
		output-earpiece: Output to earpiece (priority 200, latency offset 0 usec, available: yes)
			properties:
				
		output-speaker: Output to speaker (priority 300, latency offset 0 usec, available: yes)
			properties:
				
		output-wired_headset: Output to wired headset (priority 100, latency offset 0 usec, available: no)
			properties:
				
		output-wired_headphone: Output to wired headphone (priority 100, latency offset 0 usec, available: no)
			properties:
				
		output-bluetooth_sco: Output to bluetooth sco (priority 100, latency offset 0 usec, available: yes)
			properties:
				
		output-sco_headset: Output to sco headset (priority 100, latency offset 0 usec, available: yes)
			properties:
				
		output-sco_carkit: Output to sco carkit (priority 100, latency offset 0 usec, available: yes)
			properties:
				
		output-aux_digital: Output to aux digital (priority 100, latency offset 0 usec, available: yes)
			properties:
				
		output-speaker+wired_headphone: Output to speaker+wired headphone (priority 100, latency offset 0 usec, available: no)
			properties:
				
		output-parking: Parking port (priority 50, latency offset 0 usec, available: yes)
			properties:
				
	active port: <output-speaker>

fredldotme

@c4pp4 looks sane at first glance. It would be interesting to know how it behaves with different sample settings provided through the touch.pa file. Does it now allow forcing the sample rate that way? In that case even better, but it looks like it should work on all Sony devices.

Would you like to prepare a PR for it, so it has your name in the commit history?

c4pp4

@fredldotme
It should work on all devices using 'hardware/qcom/audio'. Now it takes default settings from pulseaudio (44.100 kHz) if it's not specified through /etc/pulse/daemon.conf. You can override it changing 'default-sample-rate' parameter. You can change the sampling rate through /etc/pulse/touch.pa as well using 'rate', 'sink_rate' or source_rate' parameter when loading module-droid-card-24.

fredldotme

@c4pp4 awesome stuff! Should give us more flexibility should the default not provide a sufficient audio experience. Will you prepare a PR for it? I'm currently off my normal setup, only carrying a backup of Halium 7.1 on a microSD card.

kalle.kruse

Thanks again for the great port, @fredldotme! I have been using the Xperia X as my daily driver for months already and I am pretty happy with it. I have been observing a number of issues, and before creating bug reports I would like to make sure they are not specific to this port and that there are no easy fixes:

Under "Updates" I see an "Ubuntu touch Version 320" update but when clicking on "Restart & install" nothing happens.
Sometimes when the screen has been locked and turned off for a long time the device takes ages (>10sec?) to wake up.
On openstreetmap.org I cannot scroll the map in Morph Browser. I am pretty sure this had been working before on the bq Aquarius E4.5.

And a question: Is there any hope to get autofocus to work for the camera?

dan.socea

Hello!
Are there any plans on moving to ubuntu 20.04, or this is not possible due to Xperia X's hardware?

flohack

@dan-socea We will move to 20.04 and the Xperia X should not have an issue for that, as its just about kernel version to be high enough for systemd to run.

dan.socea

@Flohack That is great to hear, that there is still some life left into this device.