Fairphone 2 (FP2)

[Fla]

@Luksus thanks, I did the update and everything worked well. In your script to install gst-droid, you should remove the holding of qtubuntu, this package isn't there anymore (see original topic: UPDATED: qtubuntu packages have been removed from the repository, thus no pinning is required anymore).

[Fla]

@Luksus well no, everything isn't working fine: I can't do phone calls. I call someone, we can discuss and then after less than a minute, I can't hear the other participant anymore. At that time, the button to hang isn't working.

@peat_psuwit did you change anything in the halium part since a few months back?

[peat_psuwit]

@Fla The only change recently is the addition of repowerd config file.

[Luksus]

@Fla for me it works with the rootfs from 12 days ago. So I assume it could be caused by the rootfs build you have used.

[Fla]

The phone call feature itself isn't the problem, the problem is the lost of the network. But after a few days (maybe thanks to a reboot?) I don't have it anymore. It looks like network signal isn't really good, no idea if it's related to that new port, to the phone hardware itself, to UT in general, or because of the carrier... But the problem is mainly gone anyway.

[Fla]

@peat_psuwit I would really love to be able to have OTA update on my FP2 running that port. Is there anything I can do to help you make it official?

[Luksus]

Since Fairphone managed to run Android 9 on the FP2, would it be possible to create a Halium 9 Port with this GSI thing?
https://www.fairphone.com/en/2020/06/18/fairphone-2-gets-android-9/

[jezek]

@Luksus said in Fairphone 2 (FP2):

Since Fairphone managed to run Android 9 on the FP2, would it be possible to create a Halium 9 Port with this GSI thing?
https://www.fairphone.com/en/2020/06/18/fairphone-2-gets-android-9/

I've asked the same question on fairphone forum. The answer is:

No, because of
Halium version 9 is basically for phones released with android 8 or later, in other words devices with vendor partition.
The FP2 does not have a vendor partition.

[Luksus]

I finally managed to build a new halium-boot and system image. I updated my post above.

And here is a "version-bumped" version of the gst-droid camera app:
https://drive.google.com/file/d/1sV8te8sS-a7qCd-bjmEWxl0UFJo-Ma-9/view?usp=sharing

With this, my camera is working again.

[Fla]

@Fla said in Fairphone 2 (FP2):

@peat_psuwit I would really love to be able to have OTA update on my FP2 running that port. Is there anything I can do to help you make it official?

@peat_psuwit you didn't answer to that, but as all work deserves a salary as we say in french, I precise I'm willing to pay you $100 to see 7.1 based port released as the official port for the FP2.

[peat_psuwit]

@Fla We're working towards that goal, but the base system requires more changes to support Halium 7.1 ports better before we can release any Halium 7.1 port as an official port.

[Fla]

@Luksus I just flashed it, I'll tell you if everything is fine

[Fla]

@peat_psuwit said in Fairphone 2 (FP2):

@Fla We're working towards that goal, but the base system requires more changes to support Halium 7.1 ports better before we can release any Halium 7.1 port as an official port.

So, I asked in the last Q&A what was the status of the core changes still needed for Halium 7.1 ports and the answer was:

Actually it has progressed very well and is effectively now ‘done’. The issues remaining are likely to be device specific. On Xperia X for example there are Bluetooth problems. We suggest you try it out with a Fairphone 2 and send in some test reports. Rachanan has a pretty good overview on it.

So... Here I am again ^^ What's the next step to see that port an official one, and how can I help you reach that state?

[peat_psuwit]

@Fla

The biggest issue currently is that the phone tends to reboot itself when trying to power it off. The issue has been traced to be related to the Android container. However, I haven't looked into it further.

Other than that, there are some other issues I can't remember off the top of my head. There's also the USB mode issue, but that I prefer a more proper solution than the one currently implemented in other ports.

[flohack]

Its also that current classic builds for the core devices allow adb next to MTP mode, and hotspot is a big issue. Speakerphone might not work, etc. So when we would deliver it as it is now, many people would feel a regression probably. Sorry to say, it needs more time and hands to finish that.

Same goes for OPO and N5.

[Fla]

@Flohack said in Fairphone 2 (FP2):

So when we would deliver it as it is now, many people would feel a regression probably. Sorry to say, it needs more time and hands to finish that.

I was not asking to publish it now, just what are the next steps and if I can help (by being a tester, mainly).

[Ingo]

@peat_psuwit said in Fairphone 2 (FP2):

The biggest issue currently is that the phone tends to reboot itself when trying to power it off. The issue has been traced to be related to the Android container

That happened on stock ROM as well. IIRC it was fixed at some point. Until then, the workaround was to enable the torch before shutting down (no kidding!).

[Fla]

@Ingo yep I confirm that.

[Lakotaubp]

The new place to chat https://forums.ubports.com/category/64/fairphone-2