Fairphone 3/3+ (FP3/FP3+) Port - Halium 10

[Luksus]

@oden said in Fairphone 3/3+ (FP3/FP3+) Port - Halium 10:

When I was outside, the WiFi icon was just an outline whereas the mobile network was full. The connection was still 3G but no mobile data

If it is like this, then the networkmanager is not getting an internetconnection at all, even if it is there at the sim card.

Awesome, that it is working for you now.

[Oden]

@luksus I am outside going for a walk and both GPS and mobile data are working. After setting the APN, the WiFi icon isnt showing anymore. Just the mobile network bar with a little L square next to it.

[Oden]

Hi! I have been outside today with my kids and I noticed something:

I used bluetooth headset all afternoon (12pm to 4pm connected but not playing anything) and noticed that the FP3+ got really warm in my pocket. I went to check it out and the battery was at 15%. I left the house with 80%. I guess bluetooth drains battery a lot more than before. I ised to have the same headset connected to the FP3+ the entire day without issues.

I also got a call but I couldnt get the call through the headset. Is there a setting I need to do to be able to use the headset for calls? The headset works for music (Futify) just fine though.

[Oden]

Seems like my battery issue might be something else than bluetooth. I came back home for dinner and recharged my phone fully. It went from 100% down to 38% in 5h with minimal use (been playing Red Dead Redemption 2 all evening). It is strange to see the battery drain so quickly. Any suggestions or recomendations on what could be causing this?

[Luksus]

@oden is it still running hot without doing something?
Did you do a reboot in the meantime?

[Oden]

@luksus I rebooted after charging it overnight. So far, it hasnt been incredibly warm. Its been roughly 2 hours since the full charge and its at 86%. Im heading to the zoo with the kids. I can update on the battery status when we are on our way back.

Minor update: 40min after my previous post, I can feel the FP3+ heating up in my pocket. The battery level is at 74% as I type this. Losing 12% battery when it has been in my pocket is probably an issue.

[cr9c]

This post is deleted!

[Luksus]

@oden Hi, I also encountered the heating issue, though I don't know, what caused it.
I noticed, that it gets hot in the lower left corner on the backside, but I don't believe it's caused by the NFC chip...

I got the Impression, that it has somethin to do with mobile data/cellular network.
I believe it cooled down, when I disabled mobile data, and it did not get hot again, after turning it on again...

[Luksus]

Hey, with the latest build video recording should work now.
I also added some short instructions for waydroid in the first post.

[Contralto]

Hi @ all,

I have now time to install and test the newest version again.

Unfortunately I have deleted all my data by unlocking the boot manager
But that makes it a lot easier to back up the data * lool *

I´m currently downloading the image to first flash android and then the halium-image.

Should take a while, I will respond what things are working and what not

[Contralto]

Hi again,

I have installed the new system now.
First thing I try is to use the new anbox.

Anbox-Halium is installed successfully and showing the following:
Kernel: OK
System: OK
Enabled: YES
Running: YES

But, there is always no internet connection
I have installed a app and use adb shell with ping, but no connection
Some ideas ?

I must get some apps working this week or switch again to /e/os.... ;(

[Contralto]

Some more informations:

2|armv7-a-neon:/ $ ifconfig
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0 
          inet6 addr: ::1/128 Scope: Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:16 errors:0 dropped:0 overruns:0 frame:0 
          TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0 txqueuelen:1 
          RX bytes:1784 TX bytes:1784 

eth0      Link encap:Ethernet  HWaddr b2:73:18:d9:39:98
          inet addr:192.168.250.2  Bcast:192.168.250.255  Mask:255.255.255.0 
          inet6 addr: fe80::b073:18ff:fed9:3998/64 Scope: Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:28 errors:0 dropped:0 overruns:0 frame:0 
          TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 
          collisions:0 txqueuelen:1000 
          RX bytes:2216 TX bytes:2632

ifconfig system itself:

anbox0    Link encap:Ethernet  HWaddr fe:2a:b3:d5:a0:e9  
          inet addr:192.168.250.1  Bcast:0.0.0.0  Mask:255.255.255.0
          inet6 addr: fe80::fc2a:b3ff:fed5:a0e9/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:25 errors:0 dropped:0 overruns:0 frame:0
          TX packets:29 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2352 (2.3 KB)  TX bytes:1900 (1.9 KB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:13594 errors:0 dropped:0 overruns:0 frame:0
          TX packets:13594 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1 
          RX bytes:42874430 (42.8 MB)  TX bytes:42874430 (42.8 MB)

rmnet_data0 Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          inet addr:10.153.4.213  Mask:255.255.255.252
          UP RUNNING  MTU:1280  Metric:1
          RX packets:12 errors:0 dropped:0 overruns:0 frame:0
          TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1088 (1.0 KB)  TX bytes:1000 (1000.0 B)

rmnet_ipa0 Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          UP RUNNING  MTU:2000  Metric:1
          RX packets:10 errors:0 dropped:0 overruns:0 frame:0
          TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1232 (1.2 KB)  TX bytes:1104 (1.1 KB)

rndis0    Link encap:Ethernet  HWaddr ce:52:67:4b:4b:b2  
          inet addr:10.15.19.82  Bcast:10.15.19.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

rndis1    Link encap:Ethernet  HWaddr 96:9f:ef:40:8c:0e  
          inet6 addr: fe80::f580:2371:b587:c8e1/64 Scope:Link
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

vethG19L1N Link encap:Ethernet  HWaddr fe:2a:b3:d5:a0:e9  
          inet6 addr: fe80::fc2a:b3ff:fed5:a0e9/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:25 errors:0 dropped:0 overruns:0 frame:0
          TX packets:34 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2702 (2.7 KB)  TX bytes:2636 (2.6 KB)

wlan0     Link encap:Ethernet  HWaddr 84:cf:bf:93:0e:b1  
          inet addr:192.168.178.80  Bcast:192.168.178.255  Mask:255.255.255.0
          inet6 addr: fe80::b9bc:13b6:a60c:f404/64 Scope:Link
          inet6 addr: 2a02:2454:8b64:7400:649b:946e:40d8:5a94/64 Scope:Global
          inet6 addr: 2a02:2454:8b64:7400:8012:a19a:5db9:2495/64 Scope:Global
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:6502 errors:0 dropped:0 overruns:0 frame:0
          TX packets:713 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:395733 (395.7 KB)  TX bytes:95722 (95.7 KB)

sudo anbox-bridge restart:
no errors

Tried on WiFi and on LTE

[Luksus]

@contralto it sounds like if you are using the old anbox... New anbox-halium has nothing to do with anbox-tool app.

Did you follow my updated instructions in the first post?

[Contralto]

Hi @luksus,

Yes, I do your steps and remount the whole system, changed it to the same priority, upgraded the system and then execute the following command:
"wget -O - https://github.com/Anbox-halium/anbox-halium/raw/lineage-17.1/scripts/install.sh | bash"

[Luksus]

@contralto ok, and did you run the container with sudo /home/anbox/run-container.sh ?

[Contralto]

@luksus yes.
But...
Oh...
I think...
...all things must be do/installed in this container ?

Ops, that´s my failure
I will try it again, if I have some time...

[Luksus]

@contralto i will clarify instructions in the first post...

[jesta030]

@luksus Is there a way to buy you a coffee/beer to help developement along? I'd love to have Ubuntu on the Fairphone 3+!

[Luke]

@jesta030 I would want to help too, if possible!

[Luksus]

@luke @jesta030 basically you already can install Ubuntu Touch on your FP3+, as described in the first post.
I use it as daily driver.

@jesta030 please note, that Ubuntu Touch is not Ubuntu (like on desktop). You may be a bit disappointed, if you expect this.