Installing - connection to device lost

Lakotaubp · 1 Oct 2021, 12:02

@moem you can just boot back to twrp and you need to look under advanced wipe otptions. Clear format to ext4 cache and data. Then try again. You might need to do system as well.

Moem · 1 Oct 2021, 12:08

This post is deleted!

Moem · 1 Oct 2021, 12:49

@lakotaubp said in Installing - connection to device lost:

under advanced wipe otptions. Clear format to ext4 cache and data. Then try again. You might need to do system as well.

Okay, I managed to do this. But I'm still getting the same error:
Installing - connection to device lost

And it also pops up a notification about not being able to mount something. Here's an example, but the numbers differ a bit:

Moem · 1 Oct 2021, 13:36

The installer offered to reinstall OxygenOS, and that worked! So at least the thing boots again. More experiments to follow soon.

Lakotaubp · 1 Oct 2021, 17:42

@moem Original thread https://forums.ubports.com/topic/3253/oneplus-3-3t/616 very long and a bit of a ramble. Start at about 5th Nov.

Moem · 1 Oct 2021, 17:49

@lakotaubp I don't see anything relevant in that thread... maybe I'm missing something?

Lakotaubp · 1 Oct 2021, 18:14

@moem https://forums.ubports.com/topic/3253/oneplus-3-3t/59 fromm the 5th Nov 2019 is where the first mention of using TWRP starts down to about 19th it might give some hints on how to sort it.

Moem · 1 Oct 2021, 18:17

@lakotaubp Ah, THAT fifth of November! Will check, thank you.

Edit: I see a lot of mentions of using TWRP for wiping cache/data/system partitions... which I have done at least five times today in different ways.
No success yet.

Lakotaubp · 1 Oct 2021, 20:21

@moem Just found this
libremax Just trying to think what I did with twrp. Wipe option, format data-select yes, then in advanced wipe repair change system and data to ext4 then reboot. Then just ran the installer with wipe and bootstrap, booted to fastboot then recovery for the rest. I do remember it took ages for the spinning circles to appear to say it was flashing the device. Remember thinking it had not worked at first. Maybe leave it a little longer rather than force reboot but bit confused I must admit.

But that's about all. Will keep looking

Moem · 1 Oct 2021, 20:23

@lakotaubp said in Installing - connection to device lost:

Then just ran the installer with wipe and bootstrap,

I know about the wipe, but what is the bootstrap?
It does not take long at all to tell me it's flashing. It always fails during the 'pushing files to the device' phase. And I never try to reboot at all... there is, after all, nothing to reboot.

Thank you for your time!

Lakotaubp · 1 Oct 2021, 20:34

@moem It was an option given in the installer is it not there now? Also found this from Flohack

FlohackFlohack 31 Jan 2021, 08:34
@sven Also delete system partition to be sure - If there was encryption used for data before, it needs to be formatted, a simple wipe wont work.

Might not help but explains why.

Moem · 1 Oct 2021, 20:40

@lakotaubp said in Installing - connection to device lost:

It was an option given in the installer is it not there now?

I see two options: First Install (tick if the device was running Android before) and Wipe Data. Dalton advised me to tick them both.

I've wiped all the things.... so many times. And done a factory reset, and reinstalled Oxygen. All partitions show up as Ext4.
I don't by now even remember what I've tried.

Lakotaubp · 1 Oct 2021, 20:45

@moem Sounds like time for a break and come back fresh. Packing in for today soon myself . Good luck and will keep thinking.

Moem · 1 Oct 2021, 20:55

@lakotaubp said in Installing - connection to device lost:

Sounds like time for a break and come back fresh.

You are most likely right. Thank you, again, for your time!

cela · 2 Oct 2021, 14:11

@moem I found that it is better to tick "First Install" regardless, then the installer guides you through what you need to do in TWRP recovery to prep the partitions, I also found that if you untick "Wipe Data" the install completes to 100%, otherwise I get the connection lost dialog at around 75% if I tick "Wipe Data".

I can 100% complete the install every time now but my device freezes on the 2nd reboot after install.

I am using UBports installer version 0.8.6 beta on Endeavour OS. It might help if anyone has success to let everyone know which installer version they are using and on what OS.

I am thinking of getting access to a Windows machine to see if it makes a difference, I have tried different usb cables in both front and rear USB ports.

Moem · 2 Oct 2021, 15:17

@cela said in Installing - connection to device lost:

I also found that if you untick "Wipe Data" the install completes to 100%

Holy macaroni. You, kind sir/madam/other, are the hero of the day. This was the winning tip. My Op3 is now proudly running UT!

my device freezes on the 2nd reboot after install.

I will report back once I know whether mine does that too. I used the 0.8.9 .deb on Linux Mint.

Lakotaubp · 2 Oct 2021, 15:25

@moem Now that is something to remeber, and well done on sorting it.

Lakotaubp · 2 Oct 2021, 15:26

@cela That no wipe thing is one to remember. Thanks.

Keneda · 2 Oct 2021, 18:33

@lakotaubp
That no wipe thing is one to report

Lakotaubp · 2 Oct 2021, 18:35

@keneda @Moem has already done that and it will be looked into. If anyone else has a similar issue please let us know device and installer version.