Just got a phone and loaded UT using the installer. I've got no WIFI and no cellular data.
-
@bibaleebu You could try toggling airplane mode on and off and then checking the Apn settings under Mobile in system settings. Sometimes they are not detected correctly. If not that try the installer again and choose the halium option.. Do you happen to know if they were all working OK before flashing UT.
-
@lakotaubp They were both working fine. The phone came with lineageOS and they tested find on that. I tried toggling the airplane several times, as well as checked the WiFi settings for the battery to no avail. For the cellular, it's possible that the APN settings aren't correct but I have no idea which of the numerous ATT options is correct.
-
@bibaleebu https://forums.ubports.com/topic/6275/issues-with-cell-service-can-not-figure-out/7?_=1623798641085
Try these for ATT MMS... I will have to get one for internet.
-
@bibaleebu Just noticed you already tried halium devel. Coming from Linage should be OK but if nothing else there is the option of reflashing to the stock OS then re installing UT. Or try this https://forums.ubports.com/topic/6193/article-needed-for-firmware-upgrade/16 but read all of it there are two files needed.
-
@lakotaubp Is Lineage not the stock OS? It's what was on the phone when I bought it but it is refurbished.
-
Just for anecdata, I'd like to mention that I have installed UT on a phone (OpO) that was running LineageOS, and did not have this problem.
-
@moem That's what I would expect this is odd.
@bibaleebu It shuld work onLinage but no the stock OS would have been cyanogen or something similar on The OnePlus 1 it should be on thier site. I have had two of these both without issue. Try everything else first though. Think this issue is on the Forum somewhere but can't remeber exactly. -
@bibaleebu I have WiFi and data on mine, I'd try a factory reset and a reinstall if you haven't gotten any further
-
@totalrando I did that and same boat. I reinstalled lineage and again everything worked fine. I found cyanogen and flashed that, tested the wifi and cellular data and they worked. I tried UT again and now it won't even boot. If I do the stable release, it cycles every 5 or so seconds. If I use the halium, it just stays at the splash screen. I knew I should have just gotten a pixel 3a but I wanted to most complete experience and OPO was at the top of the list. I'm going to try and go back to lineage and see if that can boot.
-
@bibaleebu I do hope you get it to work. The OPO is effectively feature complete.
-
Getting cyanogen up and running involved flashing a bunch of partitions in fastboot and I think one of those must be incompatible with UT. Does anyone know where I can get some that work?
-
@bibaleebu Why are you flashing when you can use the installer? And the stock OS is OOS9 If I remember right.
-
@bibaleebu We normally say to go back to the last version of the original device OS so you have all the correct updates and firmware and that the partions are correct for UT as it uses the original partion sizes. Why that is now causing an issue if dev mode, usb debugging and stuff is done I'm at a loss.
Please double check everything and as @TotalRando says if the installer now does install the original OS try that. It been some time since I did a OPO and didn't know the installer did that now for the OPO. You learn something every day. Then you just have to remember it
-
@lakotaubp @bibaleebu Found a video for installing stock ROM for OPO. I literally flashed mine with the installer out of the box and haven't gone back. This has links to the files in the description. https://www.youtube.com/watch?v=WhPccnk7uSg
-
@totalrando Those were the steps I followed after someone recommended going back to stock. And I'm flashing only because that's the tutorial steps I was originally following. Additionally, any attempt to install oxygen fails because I get the error "This package is for Oneplus devices: this is A0001". I'm on linux and most single step installers (when I can find them) only tend to work on windows or mac so I break the *.bats open and just walk through the steps one at a time. I'm feeling more and more out of my depth with each passing attempt.
I also can't find any older oxygen OS releases. The oneplus website seems only to have the newest.
-
@bibaleebu On the YouTube (I know people hate these videos) there is a link to XDA's list of CM releases. https://forum.xda-developers.com/t/rom-ota-mirrors-for-official-cyanogen-roms-and-ota-updates.2906746/
I'd try the earliest.
-
@bibaleebu Just to clear things up when I said use the latest OS version for the device. I meant the for your specific device the OPO - A0001. If you install that it should correct all the partions sizes and so on. Both of my OPO had the old Cyanogen OS on them and I went straight from there to UT. As another option maybe @Moem can remember the version of linage that was on their OPO.
-
@lakotaubp said in Just got a phone and loaded UT using the installer. I've got no WIFI and no cellular data.:
As another option maybe @Moem can remember the version of linage that was on their OPO.
I think it came with 15.1... but I'm not absolutely certain.
-
@moem Thanks it might be a help.
-
@lakotaubp I just bought one cause my FP2 was driving me insane. It should come in a couple of days. I don't know what rom's on it, but another seller claimed to have had lineage 18 installed on it. If it's true, it's a custom rom, but it should do the trick, firmware and partition wise, no ?
