Oneplus 3/3T
-
Call now do work on the latest release
also camera is somewhat working on arm64.And you can now install it with the installer
-
Trying the installer with Oneplus3T but it cannot get past the 'Sending...' screen so far. I've waited for 30 mins or so. That should be enough, no?
Edit
The phone is showing Android Recovery screen with options: 'reboot system now', 'ubuntu actions, and 'android actions'. Screen is otherwise black (there was a flash of colour that looked as though it might have been the android robot lying down, but it was only there for a fraction of a second). Phone getting quite warm.Previous experiences suggest I should go and get a better cable!
-
@ziggutas I had to reboot into the recovery again before it would send.
-
@PhoenixLandPirat Ah, thanks for that. I'll give it a go.Unfortunately my laptop has just packed up (I'm typing on pc) and other matters are calling for attention so I might have to leave this until tomorrow.
Will report back later...
-
@mariogrip have you test calling to and from Op3? On Vince's port the calling on to Op3 is broken(sound and mic don't work, screen won't wake up only upon pressing power button) Calling from Op3 works fine.
I'll test this arm64 version. -
@ziggutas said in Oneplus 3/3T:
Trying the installer with Oneplus3T but it cannot get past the 'Sending...' screen so far. I've waited for 30 mins or so. That should be enough, no?
Edit
The phone is showing Android Recovery screen with options: 'reboot system now', 'ubuntu actions, and 'android actions'. Screen is otherwise black (there was a flash of colour that looked as though it might have been the android robot lying down, but it was only there for a fraction of a second). Phone getting quite warm.Previous experiences suggest I should go and get a better cable!
Hi all! Having same issue, stuck at this step. Device - OnePlus 3T, trying to install from Windows version of UBPorts installer. Any advice or instructions please?
P.S. Also tried to 'reboot to recovery as PhoenixLandPirate suggested - did not help.
-
@mariogrip rather a nice experience to install on Op3t, well done, thanks for your hard work Marius.
How to enable FLASHLIGHT? Should I install: sudo ubports-qa install PR-22
? -
@pglushkov same problem here....
-
Today tried again, but this time running UBPorts Installer on Ubuntu 18.04, deb-version. Still have same result. UBPorts stdout says:
peter@peter-pg-lt-gps:~$ sudo ubports-installer Gtk-Message: 16:10:56.149: Failed to load module "canberra-gtk-module" info: Welcome to the UBports Installer version 0.4.5-beta! Pug interceptor registered successfully info: Downloaded file 1 of 1 checked: keyring-4c4e7ef380ebcfa2c31084efa199138e93bfed8fc58aa3eb06bdf75a78af9b57.tar.xz true checked: version-5.tar.xz true checked: device-b4422d1593b76acedd819149ddb24b505a9cc345c6d73cf8094996a926b44ca1.tar.xz false checked: ubports-ab82f71538d423d2ede781431e719918bb0c3450f148c230407f58083c9b7e77.tar.xz true checked: device-b4422d1593b76acedd819149ddb24b505a9cc345c6d73cf8094996a926b44ca1.tar.xz true info: Good bye!
UI of installer still says 'Sending ...' endlessly, device stays at this 'reboot system now'/'ubuntu actions'/'android actions' menu. No reboots could help, nor to 'recovery', nor to 'fastboot'.
Any advice? Thanks!
-
Could all of you with flashing problems please do the following...
You will need a computer with the
fastboot
package installed.- Boot to bootloader
- Run the command
fastboot format:ext4 cache && fastboot format:ext4 data
- Attempt installation again
It appears the problem is ADB trying to read a file from the data partition, failing, and simply blocking all connections.
-
@UniSuperBox Thanks for the instructions; will try this in the next few days and post back here with the outcome.
-
@UniSuperBox said in Oneplus 3/3T:
Could all of you with flashing problems please do the following...
You will need a computer with the
fastboot
package installed.- Boot to bootloader
- Run the command
fastboot format:ext4 cache && fastboot format:ext4 data
- Attempt installation again
It appears the problem is ADB trying to read a file from the data partition, failing, and simply blocking all connections.
Please note this will DELETE all data on the device.
-
@mariogrip said in Oneplus 3/3T:
@UniSuperBox said in Oneplus 3/3T:
Could all of you with flashing problems please do the following...
You will need a computer with the
fastboot
package installed.- Boot to bootloader
- Run the command
fastboot format:ext4 cache && fastboot format:ext4 data
- Attempt installation again
It appears the problem is ADB trying to read a file from the data partition, failing, and simply blocking all connections.
Please note this will DELETE all data on the device.
Thank you @UniSuperBox and @mariogrip for your replies!
Tried to follow your instruction from above, two issues:
- When trying to format 'data' partition, fastboot returns error:
D:\Tools\platform-tools>fastboot format:ext4 data Warning: data type is , but ext4 was requested for formatting. fastboot: error: Couldn't parse partition size '0x'.
- I seem to have 'userdata' partition on my device and formatting it to ext4 goes successfully.
After that, installation procedure does not seem to progress, again stuck at same point. Mb something should be done with this 'data' vs 'userdata' situation?
-
@UniSuperBox said in Oneplus 3/3T:
Could all of you with flashing problems please do the following...
You will need a computer with the
fastboot
package installed.- Boot to bootloader
- Run the command
fastboot format:ext4 cache && fastboot format:ext4 data
- Attempt installation again
It appears the problem is ADB trying to read a file from the data partition, failing, and simply blocking all connections.
Ran the command and noticed the word FAILED at the bottom of the output. Is that a problem?
Tried installer again, but still stuck on 'sending files' step of the process after 40 mins.
Phone will not boot into android anymore at the moment; it doesn't get past the spinning red and white dots. I'm not concerned about this necessarily...maybe I should be?file:///home/chris/Pictures/ubp-installer6Nov19,07-32am.png
-
@ziggutas try the same command but with userdata instead of data
-
@vince1171 said in Oneplus 3/3T:
@ziggutas try the same command but with userdata instead of data
Hi!
Please look at my message just above the one of @ziggutas . I tried to format 'cache' and 'userdata' partitions separately - it did not help. -
@vince1171 Thank you kindly for that. The modified command seemed to complete its task. Ran the installer again and it got a bit further this time, but errored out just after the 'sending files' stage.
There was the 'Yikes' pop up window with details but I didn't know how to save the info, sorry. Screenshot of Terminal might help?
Edit: I tried to carry on for 2nd time but it got stuck on 'sending files'
file:///home/chris/Pictures/ubp-installer,6Nov,16-26pm.png
-
For those getting
"fastboot: error: Couldn't parse partition size '0x'."
I fixed this by dropping into TWRP recovery and fixing /data. I had messed up /system as well and needed to fix that too
From TWRP I set /data to ext4 and then ran the installer. The files were able to send successfully and the installation completed.
The other nice thing about using TWRP was that it has a terminal built in so I was able use df to confirm that the partition was correct.
-
Tried all the suggestions and am also getting stuck at "sending". By flashing twrp and switching data to ext4 as suggested above, I was able to format: ext4 cache and userdata without errors. but the first run of the installer I get the Yikes! page, immediately running the installer again i get stuck at sending while the phone shows fastboot mode. I waited 15/20 minutes.
-
I was able to get it to install now, not sure I could reproduce.