Can't update Aquaris M10 FHD Frieza
Keneda last edited by
Your PC's on Linux or windows?
Did you put FH10 in dev mode before trying?
I flashed the same device a few days ago. Before you run the tool from UBports, you will start the SP_flashtool. In my case that did not start, and I looked into the guidance https://wiki.ubuntuusers.de/Ubuntu_Touch/flash_tool/. They mention a BROM-error - as recommended there I disabled the modemmanager, and started the SP_flashtool again. This time it ran through, and after the UBports-tool is successful.
Thanks for your answers.
No better luck so far... tried a different cable and usb port. Still the same...
Tried installing the original ROM, I don't have any error, flash_tool tells me everything went fine... and the tablet still freezes at the "powered by ubuntu" splash screen...
Same goes with ubports-installer...
@nterr This might be useful it might not https://web.archive.org/web/20180118130643/http://www.mibqyyo.com/en-articles/2015/09/16/ubuntu-android-installation-process-for-bq-aquaris-e4-5-and-e5 process is the same for your device.
Got the old rom working (OTA15).
Still can't get ubports-installer to install the update correctly. Still the same problem I described in my first post.
Basically I'm still stuck at the exact same point.
I forgot to respond to this :
- Yes dev mode was activated
- I'm on linux.
when you turned dev mode on did you get The little window and click the " ALLOW " option ,like you do with adb connection.
i forgot to say ,you should reboot after doing that. ( i have this device and swap OS`s , it can be picky at times).
if you still have no access to it, reflash Ubuntu with flashtool ( not with the Format all option).
if you are "bricked" pull the cover off ( no wires are stuck to anything ) disconnect the battery , reflash wth flash tool ,then reconnect battery , and try again.
@nterr If you can use the snap installer try that, you can watch in a terminal where the issue arrives. Reboot to recovery and clear cache and try again with the snap installer. We have had a few issues recently with adb dropping out for some reason you could also try checking thats is working ok.
Flashed back to the old rom with flash tool (ota15, working fine), checked if dev mode was correctly activated, it was, rebooted just in case, rebooted again, cleared cashed, used ubpoters-installers from the snap repo, rebooted to bootloader, and everything just seems to work fine... This is what I get in the terminal :
info: Welcome to the UBports Installer version 0.4.18-beta!
info: Downloaded file 1 of 1
checked: keyring-4c4e7ef380ebcfa2c31084efa199138e93bfed8fc58aa3eb06bdf75a78af9b57.tar.xz true
checked: version-9.tar.xz true
checked: device-6e23e473ab0b5bd2baa820e442b41d22fe20d76f8ca984e2fb22bf47597a5eb0.tar.xz true
checked: ubports-a1f443971032f2b6a03ed6f83d3340e026d59bfbe1625b259fb77eb05fa2b6a9.tar.xz true
info: All done! Your device will now reboot and complete the installation. Enjoy exploring Ubuntu Touch!
But it's still stuck at "installing ubuntu update."
AppLee last edited by AppLee
This step can take some time to proceed.
The installation files were successfully copied to the phone.
But now it needs to unpack it and put it in the right partitions. I don't remember how long it can take, but it's safer if your phone is fully charged or plugged to a wall socket.
What is the current status ?
Just what you said, plugged to a wall socket and stuck at "installing ubuntu update" for an hour or so... Last time I waited a couple of hours, since installer says it should take 5 minutes I assumed it was just stuck. I guess I'll try to wait longer this time...
Perhaps it would be a good idea to try a manual installation? Unfortunately I can't find the instructions; they used to be on the old device pages, but the link is gone from the new device pages... I just asked over there where to find the instructions nowadays :https://forums.ubports.com/post/31321
Maybe @AppLee knows where to find them?
AppLee last edited by
I thought that by doing a manual installation we probably are able to locate the "trouble spot", and get an idea what goes wrong here....
Hm. Sometimes it helps to use a TWRP recovery to clean the cache thoroughly. Perhaps it is worth a try, https://eu.dl.twrp.me/freezerfhd/
Or have a look at this post: https://forums.ubports.com/post/1617 The trouble is: not enough space left in the cache...
Could you try an
adb shell df -hcommand in recovery mode? That should show us the space left on the device, and the cache partition
@nterr This is a bit odd. Did you choose the wipe option when installing (if you have backed up your stuff first). Try rebooting to recovery use the options to clear the cache and try again.
adb shell "df -h"
- daemon not running. starting it now on port 5037 *
- daemon started successfully *
Filesystem Size Used Available Use% Mounted on
tmpfs 981.1M 36.0K 981.0M 0% /dev
tmpfs 981.1M 12.0K 981.0M 0% /tmp
9.3G 319.4M 9.0G 3% /data
3.8G 480.2M 3.3G 12% /cache
Well I tried already before posting what's said in this other post. But I can try all over again just in case I did smthing wrong along the way...
Tried too to install it a few different ways, using the wipe option or not, rc and stable...
What's TWRP and how should I use it ?
TWRP is an alternative recovery, which offers quite a few things you can perform from "outside" the main system. It is flashed to the recovery partition of the device using fastboot - it replaces the recovery provided by UT or the original OS. It can be used to root android devices, create backups etc, or flash the whole system with custom-ROMs. In this case it could be useful to clear the cache partition completely.
You would have to download the image from the linked twrp-site, and flash the recovery as described on the the webside. Afterwards you would have to reboot in this recovery (adb reboot recovery), and then use the tools to wipe the cache, or perhaps even erase the whole system to retry with the UBports Installer.
Ok thanks, I'll try that !
Wiped everything successfully through TWRP. Tried again. No better luck... Stuck again...
I guess these manual installation instructions would indeed be the best way to understand where the installation goes wrong...
(thanks for asking in this other thread btw)
hankschwie last edited by
Last thing I can think of: Try to flash a recent Android version onto the tablet, and then try again...
I hope we can relocate the instructions - but I can't find it on https://web.archive.org/web, I always end up on the new device page without the instructions...