So have a question about security. I read that uWolf has unlimited access to the system. Isn't that a big security risk? How do you guys see that?

And it is working for me. Thank you from me as well. This work is much appreciated.

@wally next time it happens for you before restarting the service, could you give the output off: journalctl --boot --identifier=nuntium --identifier=ofonod

@johndoe said in using Ubuntu Touch as o/s for IoT devices with RPi/Rockchip: A specific mobile DE, you could also look into, is Phosh. But it will probably not work with your remote access software. Whereas Lomiri is known to work with VNC at least. And it is in the debian repo's as @Vlad-Nirky already mentioned.

@wally Bienvenue , as stated , newbie to phone and UT, ok ,checking 3G is showing receiving and making a call, i guess you are right !! it does switch from L to 3G here too , so , learning here .

@domubpkm Thanks for the info! calls are my biggest issue, they just keep calling all day every day.

By following the method mentioned above, the GPS can be turned on.

@Simmonz Interesting. Have you tried contacting our Volla mates in their forum? There should be a more straightforward way of doing that. One of the benefits of such phones is that, since they have total control of the drivers, one can unlock the bootloader and lock it again after installing UT. Cheers.

Hi @Rondarius. Thanks, but that's overkill for my use case.

Indeed, this is a general issue with 20.04 OTA-9, and is not related to VollaX. Some apps fail to update. I guess that there's something regarding with 24.04 compatibility layer... For now I ignore those updates, and will wait for the next OTA-10 / 24.04-1.0 to update them again. [image: 1757793889979-photo_2025-09-13_22-02-17.jpg]

@poVoq Unfortunately, that's very dependent on the device, I can do it with my OP5 and my Sennheiser BT headphones

@JayH Yes, that is where I am stuck. I need to know what exactly is missing to complete the build. It's my first port, and I'm new to this. The port does reference other code via clone statements, so I have to look at that too. There are no comments that I am finding that tells me what does what. It will take me a while to figure out what each thing does and what goes where and when. I'm comparing other ports and reading some documentation, but it will be slow going on my own unfortunately.

@Wheeling-Pigeon Indeed. And either 9S/Pro/India...All share the same motherboard hardware&firmware + same built image...

@stanwood said in Call for testing: Ubuntu Touch 20.04 OTA-10: So, how will the update be rolled out to users on the stable channel? (OTA-9). Will they first receive the update to 20.04 OTA-10, then immediately afterwards the update to 24.04-1.0? Or will they have the choice between the 20.04 OTA update and the 24.04-1.0 update? I must admit that I myself am a bit lost in all this 20.04 OTA-9 users will first receive 20.04 OTA-10 as an usual update. After that, they'll be offered an upgrade to 24.04-1.0. Users can choose whether to upgrade or not. I'll try to make this more clear in our release announcement blog.

The Signal gateway for XMPP is also working again, in case someone prefers that.

@MrT10001 I genuinely cannot believe that fixed it, thank you! It cruised through the process this time, and UT is now installed

@Simmonz I have moved your topic so that it is more clear to everyone what device you have. That was relevant for your question, but you did not specify it at the start.

@smoore100 You may have to look at installing the minimum Android version requirement before going to UT. You can check with the Volla guys which one is required before upgrading to UT. Cheers.

I couldn't really leave it, so I just tried again, and now it worked? I did: Double Checked: Android is version 11 (Build fp4.fp4k.a.179.20230116 $ fastboot flashing unlock FAILED (remote: ' Device already : unlocked!') fastboot: error: Command failed $ fastboot flashing unlock_critical FAILED (remote: ' Device already : unlocked!') fastboot: error: Command failed Checked All three boxes (Including User Wipe)... Maybe you were right, Luksus (and thanks!), that I somehow missed the first check box, but alas, I'm a happy camper.. Regards Grisen

@poVoq I just tried now with the apk pure Revolut install. It installs but immediately says the device is not secure and will not start.